Stroke Single Cylinder

Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System

Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System
Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System
Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System
Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System
Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System
Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System
Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System
Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System
Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System
Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System
Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System
Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System

Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System    Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System

2.8HP 2Stroke Outboard Motor Fishing Boat Engine Manual Recoil Start System 63CC. The Outboard Motors modle of SPOE2.5 has been designed and is intended for the skippers of small boats (carrying capacity less than 4 people), powered by outboard motors and operating in near waters.

In order to avoid damage during transportation, the mast and the motor engine are packaged separately. Features 360 degree steering rotation for reverse. Start-In-Gear protection/clutch feature prohibits prop rotation while idling. Lift/Tilt feature for shallow water operation and convenience. Standard CDI ignition system for easy starting and improved performance. Vertical mount engine design for increased power, performance and durability.

Superior carbonation system with primer bulb for increased efficiency. Twist grip throttle handle and engine stop button for improved response. Superior outboard anti corrosion system and anodes for increased durability. Durable cast aluminum construction for superior corrosion protection.

Heavy duty lightweight plastic cast propeller is standard equipment. Lower engine to running position and check the following. Loosen air-vent screw on fuel tank cap by 2 or 3 turns (if fitted). Firmly connect fuel hose to both fuel tank and engine. Squeeze primer bulb until it becomes firm.

Make sure throttle grip on handle in START position. Clip lock plate onto emergency-stop switch and tie lanyard to your wrist.

Pull out choke if starting cold engine. Start motor by pulling starter handle (manual start).

Check fuel pump to ensure membrane is not torn out. Check carburetor to ensure that draining screw is not opened.

Mounting An Outboard Motor: The method of securing an outboard motor to the vessel. Use of hand-tightened screw thread clamps. These clamp the transom of the vessel between the engine mounting bracket and the screw thread plates. Their tightness should be checked each time the engine is used. A safety rope or chain should also be used to secure the motor to the vessel and prevent the motor from dropping from the boat if the clamps get loose during vessel operation.

On larger outboard motors, the mounting bracket is usually bolted through the transom plate. This is a more secure method, but regular checks must be made for looseness. Trim Angle: By changing the outboard motor's drive angle, the vessel's bow can be made to rise or fall. The performance and stability of a vessel depends a great deal on correctly trimming the outboard. Care must therefore be taken to ensure the outboard is trimmed correctly under different sea and loading conditions. On smaller outboards, the trim angle is adjusted manually by moving an adjusting rod to different holes in the mounting bracket. The bigger outboards usually have a Trim Switch fitted on the remote control level. Out put: 2.1kw (2.8HP). Bracket to Propeller Center: 400-600mm. Start system: Recoil start(manual start).

Start carburetion system: Choke start. Propeller mark: 7" 1/4"x5.

Recommended Fuel: 90# unleaded gasoline. Fuel to oil ratio: 25:1. Recommended Gear Oil: Hypoid Gear oil SAE85W/90. Instructions On Refueling: The gasoline is highly flammable and explosive: 1. Don't smoke, when refueling, keep away from fire, flame and ignitions of other sources.

Shut off the engine of your outboard engine before refueling. Use 2 stroke engine oil. The mixing ratio of gasoline and oil is 25:1.

Mix the gasoline and oil and shake well. Don't spill the gasoline. Use clean cloth wipe off the spilled gasoline.

When start the engine, keep at least 3 meters distance from the refueling point. For this 2 stroke outboard motor, you need to use gasoline and oil mixed fuel. The gasoline and oil mixing ratio is 25:1. Please use 90# unleaded gasoline and 2 stroke engine oil. We are not responsible for undeliverable address.

X'mas or other reasons. We are always working according to international standards and serve our customers from all over the world. Taking the purpose of "meeting different requirements from our overseas customers".

Your comments about our products are welcomed. We hope to have the opportunity to establish business relationships with you. Our goal is "providing you both high quality products and the best prices". Feedback is very important to us.

It is impossible to address issues if we do not know about them! Dear friend: Welcome to me my services are available: Monday To Friday: 8:30 to 18:00 (Beijing China time) 1.

If it's non-workdays, please kindly be patient and considerable to give us a little more time. Out put: 2.1kw (2.8HP) Max. Power: 1.9kw/7500rpm Bracket to Propeller Center: 400-600mm Ignition system: CDI Start system: Recoil start(manual start) Start carburetion system: Choke start Propeller mark: 7" 1/4"x5 Recommended Fuel: 90# unleaded gasoline Fuel to oil ratio: 25:1 Recommended Gear Oil: Hypoid Gear oil SAE85W/90 Notice: For this 2 stroke outboard motor, you need to use gasoline and oil mixed fuel, the gasoline and oil mixing ratio is 25:1. Please use 90# gasoline and 2 stroke engine oil. The item "Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System" is in sale since Wednesday, October 21, 2020. This item is in the category "Collectibles\Transportation\Boats & Ships\Other Boat & Ship Collectibles". The seller is "airbrushdy" and is located in New Jersey,Los Angeles,Atlanta.

This item can be shipped to United States.

  • Brand: Unbranded
  • Engine(HP): 2.8HP
  • Manufacturer Part Number: Does Not Apply
  • Stroke: 2 Stroke
  • Warranty: 2 Year
  • Ignition system: CDI system
  • Displacement: 63CC
  • Start System: Recoil start (manual start)
  • UPC: Does not apply
  • Engine type: Single cylinder
  • Cooling System: air-cooled
  • Engine model: 1E48F
  • Bore x stroke: 44mm x 34mm
  • Mixing ratio(Gasoline:oil): 25:1
  • Gasoline tank capacity: 1.2L
  • Gear ratio: Hypoid Gear oil SAE85W/90


Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System    Heavy Duty Outboard Motor Boat Strong Engine 2Stroke Manual Recoil Start System