Standard CDI ignition system for easy starting and improved performance. Vertical mount engine design for increased power, performance and durability. Superior carbonation system with primer bulb for increased efficiency.Twist grip throttle handle and engine stop button for improved response. Superior outboard anti corrosion system and anodes for increased durability. Durable cast aluminum construction for superior corrosion protection.
Heavy duty lightweight plastic cast propeller is standard equipment. Lower engine to running position and check the following. Loosen air-vent screw on fuel tank cap by 2 or 3 turns (if fitted) 3. Firmly connect fuel hose to both fuel tank and engine 4. Squeeze primer bulb until it becomes firm 5.
Make sure throttle grip on handle in START position 6. Clip lock plate onto emergency-stop switch and tie lanyard to your wrist 7. Pull out choke if starting cold engine 8.Start motor by pulling starter handle (manual start) 9. Push choke back in 10. Check fuel pump to ensure membrane is not torn out. Check carburetor to ensure that draining screw is not opened. Mounting An Outboard Motor: The method of securing an outboard motor to the vessel. Use of hand-tightened screw thread clamps. These clamp the transom of the vessel between the engine mounting bracket and the screw thread plates. Their tightness should be checked each time the engine is used. A safety rope or chain should also be used to secure the motor to the vessel and prevent the motor from dropping from the boat if the clamps get loose during vessel operation.
On larger outboard motors, the mounting bracket is usually bolted through the transom plate. This is a more secure method, but regular checks must be made for looseness. Trim Angle: By changing the outboard motor's drive angle, the vessel's bow can be made to rise or fall. The performance and stability of a vessel depends a great deal on correctly trimming the outboard.Care must therefore be taken to ensure the outboard is trimmed correctly under different sea and loading conditions. On smaller outboards, the trim angle is adjusted manually by moving an adjusting rod to different holes in the mounting bracket. The bigger outboards usually have a Trim Switch fitted on the remote control level. Out put: 1.82kw (2.5HP). Bracket to Propeller Center: 400-600mm.
Start system: Recoil start(manual start). Start carburetion system: Choke start. Propeller mark: 7" 1/4"x5. Recommended Fuel: 90# unleaded gasoline. Fuel to oil ratio: 25:1.
Recommended Gear Oil: Hypoid Gear oil SAE85W/90. Instructions On Refueling: The gasoline is highly flammable and explosive: 1. Don't smoke, when refueling, keep away from fire, flame and ignitions of other sources. Shut off the engine of your outboard engine before refueling. Use 2 stroke engine oil.
The mixing ratio of gasoline and oil is 25:1. Mix the gasoline and oil and shake well. Don't spill the gasoline.Use clean cloth wipe off the spilled gasoline. When start the engine, keep at least 3 meters distance from the refueling point. For this 2 stroke outboard motor, you need to use gasoline and oil mixed fuel. The gasoline and oil mixing ratio is 25:1. Please use 90# unleaded gasoline and 2 stroke engine oil. In order to avoid damage during transportation, the mast and the motor engine are packaged separately. We can only provide CE certification, there is no other certification can be provided, thanks for your understanding! We are not responsible for undeliverable address.
X'mas or other reasons. We are always working according to international standards and serve our customers from all over the world. Taking the purpose of "meeting different requirements from our overseas customers". Your comments about our products are welcomed. We hope to have the opportunity to establish business relationships with you.
Our goal is "providing you both high quality products and the best prices". Feedback is very important to us. It is impossible to address issues if we do not know about them!Dear friend: Welcome to me my services are available: Monday To Friday: 8:30 to 18:00 (Beijing China time) 1. If it's non-workdays, please kindly be patient and considerable to give us a little more time. Out put: 1.82kw (2.5HP) Bracket to Propeller Center: 400-600mm Ignition system: CDI Start system: Recoil start(manual start) Start carburetion system: Choke start Propeller mark: 7" 1/4"x5 Recommended Fuel: 90# unleaded gasoline Fuel to oil ratio: 25:1 Recommended Gear Oil: Hypoid Gear oil SAE85W/90 Notice: For this 2 stroke outboard motor, you need to use gasoline and oil mixed fuel, the gasoline and oil mixing ratio is 25:1. Please use 90# gasoline and 2 stroke engine oil. The item "2 Stroke 2.5 HP Outboard Motor Boat Motor 52CC Boat Engine With Air Cooling System" is in sale since Tuesday, May 26, 2020. This item is in the category "Collectibles\Transportation\Boats & Ships\Other Boat & Ship Collectibles". The seller is "youbaobostar" and is located in Los Angeles, New Jersey, Atlanta. This item can be shipped to United States.